How do I fix E4 error on treadmill?

Error code “E4” may appear in the SPEED display if the walking belt is moving at a slow speed, and there is excessive stress on the motor. Remove the key, wait for ten seconds, and then reinsert it. If you weigh over 200 pounds, it may be helpful to increase the incline of the treadmill.

What does Error 22 mean on Precor treadmill?

drive motor has
Error 22 indicates that the drive motor has been instructed to start, by either manual or program control, and the monitoring system has not received any response from the speed sensing system indicating that the drive motor has started.

What does Error 30 mean on a Precor elliptical?

30-33 Communication Errors. 35 Excessive AC Input Current Spike. 36 Excessive AC Average Input Current. 37 E-STOP Upper PCA / Lower PCA Mismatch.

What does E4 mean on a sole treadmill?

The most common cause of an E4 error is a worn belt or walking board or a walking belt that needs lubrication. To test the walking belt lubrication, do not turn the treadmill motor on. Set the elevation to the highest level.

Where is the reset button on a Precor treadmill?

Red Reset Button

Use the power switch beneath the front panel to turn. the treadmill Off.
Make sure the treadmill is located away from heating. ducts.
Wait a few minutes. Make sure the magnetic safety key.
Push the red reset button, and then turn the treadmill On.
Check the display to verify that the Precor banner is.

Do treadmills have a reset button?

Find the reset hole on the underside of the console. Plug the treadmill back in to a power outlet, insert a cotton swab or a small piece of plastic into the reset hole and push the “Reset” button.

How do I fix error 7 on my treadmill?

If the running deck is in a high incline position, use the incline down button to adjust the deck to a mid-level position. Once the unit is in the mid-level position, power the treadmill off for 5-seconds and then power it back ON. Start the treadmill.

Why is my treadmill showing error?

An E1 code just means that the console is not getting a reading from the reed switch (Speed Sensor). If the running belt moves for several minutes and then produces the E1 error, this is most commonly a result of the running belt needing lubrication. When this occurs, the running belt can no longer absorb lubrication.

What can go wrong with a treadmill?

How to Fix Common Treadmill Problems

Erratic Speed. There may be a problem with your machine if the speed varies as you’re running.
Slipping Belt. If you feel a slipping sensation when using your treadmill, it may be in need of minor treadmill repair.
No Display.
Burning Smell.
Non-Working Motor.
Heated Belt.

What is the Precor all inclusive exercise equipment error code?

Welcome to the Precor all inclusive exercise equipment Error Code and Troubleshooting Guide. This document contains all supported error event code information including the error code description, issue/Symptoms, troubleshooting, and repair information. ERROR EVENT CODES Error Code (00-19) Error Code (20-39) Error Code (40-59) Error Code (60-79)

What’s the reset button on a Precor treadmill?

When the treadmill is not in use, press the “Stop,” “ENTER” and “QUICK START” buttons in rapid succession. The “RESET” button can also be used, in place of the “Stop” button.

What does error 23 mean on a treadmill?

Error 23indicates that the speed sensor signal was lost while the treadmill was in use. Error 26monitors the speed sensor signal and verifies the speed sensor signal is appropriate for the requested speed. If the speed sensor signal is incorrect or erratic, an Error 26 will be displayed.

What does an error 26 on a speed sensor mean?

Error 26monitors the speed sensor signal and verifies the speed sensor signal is appropriate for the requested speed. If the speed sensor signal is incorrect or erratic, an Error 26 will be displayed. Troubleshooting steps Carefully, vacuum out the drive motor compartment with a static safe vacuum cleaner.